CWS039 - Transistor test pedal
This pedal was built in the same format as the OAM Panorama but included external transistor sockets so that I could easily test transistors before putting them in other pedals.
CWS021 - Boost Preamp
Dual footswitch boost with tone bypass. The right switch acts as the master bypass for the effect, while the left switch adds in the tone control for an additional boost. This pedal is used by Vicente Elizondo as a preamp for guitar, going straight into a Tascam 414 cassette recorder. A quick adjustment of the tone control on the left can easily differentiate between warm rhythm tracks and brighter lead tracks while layering onto the 4-track.
CWS020 - PTP Boost
This pedal was my first attempt at building something point to point on turret strip. I started making this boost without a plan or a diagram, and was pretty amazed at how nicely everything fit together. Sprague Orange Drop capacitors and mil-spec metal film resistors were used throughout, and their larger size worked well in spanning the distances necessary to make as few connections and use as little wire as possible
CWS017-019
These three pedals were built as refinement to the concept in CWS016. The main circuit is the same as found in CWS008, with the addition of a switch that controls a large or small boost in the bass frequencies.
CWS016
Boost pedal with modified tone section. The capacitors were selected from extended use with CWS008, to be the exact same circuit when the pedal was in its most utilized setting.
CWS015 - Dual Momentary Footswitch
Two button footswitch with TRS jack. This pedal uses momentary switches to select up/down settings on a jamman loop pedal. It is a smaller version of the FS3X schematic with the exclusion of the mode switch.
CWS014 - Tremolo Optical mod
Another tremolo based on the circuits found in CWS006, CWS007, CWS009, and CWS012. This circuit was modded with two switches, one to bring in extra depth, and another that switches in an optical component.
CWS013 - Flute Filter Fuzz
This pedal has been in the works for a long time. I suppose the story starts years ago when I scavenged an old roadside Gulbransen organ, thrilled to find it overflowing with nice reusable poly caps, resistors, switches, pots, wire, and transistors. I got out my desoldering iron and went to work, filling drawers with parts that I hoped to someday use to build pedals with, even dreaming to make 100% recycled pedals with only parts that were destined to the trash dump.
CWS011 - AB Amp Switcher
AB amp channel switcher built for live use with green (CH1) and red (CH2) LEDs. The switch will also work with any equipment that requires a TS connection using the channel 1 output.
Project 002 - Pedal board build
I have a habit of tearing apart and rearranging my pedal board for just about every tour that I go on. Earlier this year, I had switched the entire board over to a 6-channel true bypass strip and ran all the pedals through this system. The signal chain went something like, Tuner -> Tremolo -> Boost -> Tape In -> Distortion -> Spring Reverb.
CWS010
Momentary A/B switch for switching two inputs to one output. This pedal was built specifically to switch a microcassette player into the signal path when the switch on the pedal was held down.
CWS009 - Tremolo
Tremolo pedal based off of the Electronics Australia circuit. This pedal was made for Mike York of Pianos Become the Teeth.
Project 001 - Fixing an old (Boss) power supply
If you're like me, you have a whole bunch of these kinds of power supplies all mangled up and lying broken in a box or tossed in a drawer somewhere. Instead of throwing them out and buying a new one, here's a simple 15 minute process for returning your power supply to good as, or better, than new working condition.
CWS008
Boost with six-way tone rotary switch.This pedal is yet another progression of the boost circuit found in pedals CWS001-CWS004, consisting of a volume and tone control. Instead of the continuous tone control as found in CWS004, this pedal has 6 different settings which are selectable with the 6-way rotary switch.
CWS007
This pedal was made to the same specifications as CWS006, based on a circuit which was published in Electronics Australia in November, 1968. It has a similar sound to the tremolos that were built into the circuits of the amps during that time period.
CWS006
Tremolo pedal based on EA tremolo design. This pedal was built fairly true to the circuit, with minor adjustments to the controls to give them a more preferable range.
CWS005
A/B switch built for La Dispute.
CWS004
Boost pedal built with military grade metal film resistors and Sprague orange drop capacitors. This pedal was built for personal use and combines all of the elements of CWS001, CWS002, and CWS003 that I preferred for use in my own set up.
CWS003
This is a dual JFET boost, using the mu-amp/minibooster circuit. The controls for this pedal are—a 2-way gain switch, volume knob, tone knob, and a 3-way bass switch.
CWS002
This is a dual JFET boost, using the mu-amp/minibooster circuit. The controls for this pedal are—a 2-way gain switch, volume knob, tone knob, and a 3-way bass switch.